ENERpower Softpack battery 24V in format 7S12P | 1500Wh | capacity 60Ah | for Pedelecs, eBikes DIY | with Samsung 50E.
Important General Information
This 24V battery in softpack is in 7S format (25.2V-25.9V) and is manufactured with the battery cells of Samsung SDI, Murata (Sony) or Panasonic. The batteries are manufactured in cell holders made of plastic and equipped with a BMS 40A brand ENERpower. Charging is made with a spiral cable (20 - 100 cm extendable) with a XLR-3 (3 pins) connector. Discharging is realized via a discharge cable with XT90 connector (male). A counterpart XT90 is also included.
Thus, this battery is also suitable for motors with 1200 watts of power.We manufacture the softpack batteries with FR4 insulation, flame retardant and flame retardant composites consisting of epoxy resin and glass fiber fabric. FR-4 is used inter alia as an electrically non-conductive substrate in electrical circuit boards.
Compatible with 24V motors
250 watts / 350 watts / 500 watts / 750 watts / 1000 / 1200 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion battery cell: Samsung SDI INR21700-50E
Voltage (nominal): 24V (25.2V – 25.9V)
Capacity: 60Ah
Energy: approx. 1500 Wh
Configuration: 7S12P
Format: 12 ×7
Internal resistance: < 75 mOhm
Charging voltage: 29.4V
End-of-discharge voltage: 21V
Continuous discharge current: 50A = 1200 Watt
5 Sec. discharge current: 60A = ca. 1440 Watt
Weight: approx. 6.50 kg.
Dimensions
Length: 280 mm Länge
Width: 160 mm – 175 mm
Height: 70 mm
ENERpower Softpack battery 36V, format 10S2P rectangular | for Pedelecs, eBikes DIY | Super Drain
Important General Information
We manufacture a range of Super Drain batteries in softpacks in Berlin. These batteries are small in size and weight and are made with high-current INR21700-40T or INR21700-50S battery cells. The Smart BMS (Battery Management System) with a continuous load capacity of 30A is always mounted on the longest side of the battery, resulting in an approximately 20mm thicker section at that point.
This battery is designed for users who typically complete short and demanding distances, as well as for situations where overall weight plays a crucial role (off-road, inclines, etc.).
The batteries are manufactured in a 36V (10S) configuration, with options available in a 5x4 or 10x2 setup.
The softpack batteries are constructed with FR4 insulation, which is a flame-resistant and fire-retardant composite material consisting of epoxy resin and fiberglass fabric. FR-4 is commonly used as an electrically non-conductive substrate in printed circuit boards.
Additionally, this battery features an LED status indicator located on the top side of the battery. The indicator displays the battery's charge level in the following steps: "Empty," "25%," "50%," "75%," and "Full."
Compatible with 36V motors
Up to 1080 Watt
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: INR21700-40T, or INR21700-50S
Voltage (nominal): 36V (37V)
Capacity: 8Ah / 10 Ah
Power: approx. 288 Wh / 360 Wh
Configuration: 10S2P (set up: 10×2)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Continuous discharge Current: 30A = 1080 watts
Charging Current (Max): 8A
Weight: 1.6 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90 / XT-60
Dimensions
Length: 235 mm
Width: 50 mm – 70 mm
Height: 72 mm
ENERpower Softpack battery 36V, format 10S2P rectangular | 360 Wh | capacity 10 Ah | for Pedelecs, eBikes DIY | LG Chem M50.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 Watts / 500 Watts / 540 Watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
With battery cells INR21700-M50 from LG Chem
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: LG Chem INR21700-M50
Voltage (nominal): 36V (37V)
Capacity: 10 Ah
Power: approx. 360 Wh
Configuration: 10S2P (set up: 10×2)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Continuous discharge Current: 15A = 720 watts
10 minutes discharge Current: 20A = 900 watts
5 seconds discharge current: 25A = 1080 watts
Weight: 1.6 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 220 mm
Width: 44 mm – 56 mm
Height: 72 mm
ENERpower Softpack battery 36V, format 10S2P, square) | 360 Wh | capacity 10 Ah | for Pedelecs, eBikes DIY | LG Chem M50.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 540 watts / 700 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
With battery cells INR21700-M50 from LG Chem
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: INR21700-M50 from LG Chem
Voltage (nominal): 36V (37V)
Capacity: 10 Ah
Power: approx. 360 Wh
Configuration: 10S2P (set up: 5x4)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Continuous discharge Current: 15A = 720 watts
10 minutes discharge Current: 20A = 900 watts
5 seconds discharge current: 25A = 1080 watts
Weight: 1.6 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 110 mm
Width: 88 mm – 100 mm
Height: 72 mm
ENERpower Softpack battery 36V, format 10S2P, square) | 360 Wh | capacity 10 Ah | for Pedelecs, eBikes DIY | LG Chem M50.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 540 watts / 700 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
With battery cells INR21700-M50 from LG Chem
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: INR21700-M50 from LG Chem
Voltage (nominal): 36V (37V)
Capacity: 10 Ah
Power: approx. 360 Wh
Configuration: 10S2P (set up: 5x4)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Continuous discharge Current: 15A = 720 watts
10 minutes discharge Current: 20A = 900 watts
5 seconds discharge current: 25A = 1080 watts
Weight: 1.6 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 110 mm
Width: 88 mm – 100 mm
Height: 72 mm
Enerpower 36V (10S) Li-Ion battery 10Ah (360Wh) in soft pack in a BARAK bag for the luggage rack
Important general informationVery often, customers with a battery on the luggage carrier find that their battery is no longer offered in a case, or is very expensive. Owners of cargo bikes also often have problems with the conversion into electric bikes, bechause they have no space on the frame for a battery.
We designed this combination of a Li-Ion battery and a bag for the luggage rack as a solution to this challenge.The carrying bag can be flexibly attached to almost all luggage racks with Velcro fasteners.The distance from the opening in the bag (towards the motor) is quite short, saving a long cable. Thus, the electrification of the bike can be guaranteed both optically and professionally.Please note that the bag can be larger than the battery (we offer different versions). Only light materials (such as a rain jacket, for example) that do not damage the battery may be transported in the bag (no metal or sharp objects)
Technical Specifications of the bag
350 x 200 x 200 mm external dimensions
310 x 170 x 170 mm internal dimensions
10 liters
3 Velcro fasteners 40 mm wide for attachment to the luggage rack from below
2 Velcro fasteners for attachment to the luggage rack to the front (seat)
Outlet for the discharge cable with rubber coating to prevent moistureingress
waterproof cover to protect against rain
Shoulder strap detachable (included)
Reflective strips on 2 sides for safe driving.
Up to 5 kg weight
Own weight: 545 grams
Technical Specifications of the battery:
Li-ion cell: INR21700-M50T
Voltage (nominal): 36V
Capacity: 10Ah
Energy: approx. 360 Wh
Configuration: 10S2P
Construction: 5 x 4
Internal resistance: < 75 mOhm
Charging voltage: 42V
End-of-discharge voltage: 30V
Continuous discharge current: 20A = 720 watts
10 min discharge current: 25A = 900 watts
5 seconds discharge current: 35A = about 1250 watts
Weight: Approx. 1.7 kg.
Battery dimensions:
Length: 115mm
Width: 115mm
Height: 75mm
ENERpower softpack battery 36V 10Ah for eBikes, with INR21700-50E battery cells from Samsung SDI in Enerprof frame bag
Important General Information
This 36V e-bike battery in softpack is manufactured for insertion in carrier bag . With this bike-frame bag, you can attach the battery to the frame of the eBike and ideally connect it to a mid-sized engine. The frame bag is waterproof and with the separation between charging and discharging cables you don’t have to overplug constantly.
The battery cells are assembled in a plastic holder and equipped with a ENERpower branded BMS 20A-22A. The charging is done with a spiral cable (20-100 cm extendable) with an XLR-3-pin connector. Discharging is done via a discharge cable with XT90 connector (male). A counterpart XT90 is also included.
A safety fuse of 30A in a waterproof mount limits the power consumption and provides an additional safety measure.
This battery is also suitable for engines with up to 750 watts of power.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
Battery – Highlights
High-quality manufacturing – made in Germany
Assembly just-in-time
BMS with integrated passive balancer (4.1V pro rechargeable cell)
BMS with protection against overcharge, deep discharge, over-discharge (temperature monitoring)
Assembly with Samsung SDI, Panasonic (Sanyo) or LG Chem cells (subject to availability)
directly from the manufacturer
Rechargeable – After 300 charging cycles maintains 80% of the original capacity
No memory effect – charge the battery whenever you want
Environmentally friendly according to EU Directive 2002/95/EC (RoHS)
Battery – Technical Data
Li-ion Cell: Samsung SDI INR21700-50E
Voltage (nominal): 36V (37V)
Capacity: 10Ah
Power: about 360Wh
Configuration: 10S2P
Internal resistance: < 75 mOhm
Charge Voltage: 42V
Maximum Charging current: 5A
End-of-Discharge Voltage: 30V
Continuous Discharge Current: 20A = 720 watts
10 seconds 30A: approx. 1080 watts
Weight: approx. 1.50kg. / 2.2Kg. / 2.7Kg. / 3.2Kg. (Battery only)
The Enerpower frame bag is a collaboration between Enerdan and Roswheel in order to better design the Attack frame bag for use with eBike batteries. The new frame bag is: • Waterproof • Has 5 x Velcro fasteners can be attached at any point • Can be opened in 240 degrees • Suitable as a frame bag for batteries up to 5 kg. • Is approx. 350 mm long, approx. 130 mm high and 90 mm wide • Fits batteries made with 21700 format battery cells. • Has a larger opening for charging and discharging cables
Compatibility
Compatible with engines 250 watts / 500 watts / 750 watts
ENERpower Softpack battery 36V in format 10S3P RECTANGULAR | 435Wh | capacity 12 Ah | for Pedelecs, eBikes DIY | with Samsung SDI INR21700-40T
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
A smart BMS is digitally controlled and therefore more accurate. The BMS reads more powerfully and also supports recuperation.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 750 watts / 950 Watt / 1080 Watt / 1440 Watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: Samsung SDI INR21700-40T
Voltage (nominal): 36V (37V)
Capacity: 12 Ah
Power: approx. 435 Wh
Configuration: 10S3P (set up: 10x3 - rectangular)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Charge Max.: 8A
Continuous discharge Current: 30A = 1080 Watt or 40A = 1440 watts
5 seconds discharge current: 50A = 1800 watts
Weight: approx. 2.5 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 230 mm
Width: 70mm – 90 mm
Height: 74 mm
ENERpower Softpack battery 36V in format 10S3P RECTANGULAR | 435Wh | capacity 12 Ah | for Pedelecs, eBikes DIY | with Samsung SDI INR21700-40T
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
A smart BMS is digitally controlled and therefore more accurate. The BMS reads more powerfully and also supports recuperation.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 750 watts / 950 Watt / 1080 Watt / 1440 Watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: Samsung SDI INR21700-40T
Voltage (nominal): 36V (37V)
Capacity: 12 Ah
Power: approx. 435 Wh
Configuration: 10S3P (set up: 10x3 - rectangular)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Charge Max.: 8A
Continuous discharge Current: 30A = 1080 Watt or 40A = 1440 watts
5 seconds discharge current: 50A = 1800 watts
Weight: approx. 2.5 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 230 mm
Width: 70mm – 90 mm
Height: 74 mm
ENERpower Softpack battery 36V in format 10S3P square | 540 Wh | capacity 15 Ah | for Pedelecs, eBikes DIY | with Samsung 50E.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 750 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
With battery cells INR18650-35E from Samsung SDI
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: Samsung INR18650-50E
Voltage (nominal): 36V (37V)
Capacity: 15 Ah
Power: approx. 540 Wh
Configuration: 10S3P (set up: 6x5)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Continuous discharge Current: 20A = 720 watts
10 minutes discharge Current: 25A = 900 watts
5 seconds discharge current: 30A = 1040 watts
Continuous load per battery cell: approx. 3.7A and approx. 7A in peak load
Weight: approx. 2.5 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90 / XT-60 / Anderson
Dimensions
Length: 140 mm
Width: 115 mm – 125 mm
Height: 74 mm
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 540 watts / 750 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
With battery cells INR21700-M50 from LG Chem
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: LG Chem INR21700-M50
Voltage (nominal): 36V (37V)
Capacity: 15 Ah
Power: approx. 540 Wh
Configuration: 10S3P (set up: 10×3 - rectangular)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Maximal charge current: 5A
Continuous discharge Current: 20A = 720 watts
10 minutes discharge Current: 25A = 900 watts
5 seconds discharge current: 35A = 1260 watts
Continuous load per cell: approx. 4A or approx. 8A at peak load
Weight: 2.5 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 220 mm
Width: 69 mm – 80 mm
Height: 71 mm
Enerpower 36V (10S) Li-Ion battery 15Ah (540Wh) in soft pack in a BARAK bag for the luggage rack
Important general informationVery often, customers with a battery on the luggage carrier find that their battery is no longer offered in a case, or is very expensive. Owners of cargo bikes also often have problems with the conversion into electric bikes, bechause they have no space on the frame for a battery.
We designed this combination of a Li-Ion battery and a bag for the luggage rack as a solution to this challenge.The carrying bag can be flexibly attached to almost all luggage racks with Velcro fasteners.The distance from the opening in the bag (towards the motor) is quite short, saving a long cable. Thus, the electrification of the bike can be guaranteed both optically and professionally.Please note that the bag can be larger than the battery (we offer different versions). Only light materials (such as a rain jacket, for example) that do not damage the battery may be transported in the bag (no metal or sharp objects)
Technical Specifications of the bag
350 x 200 x 200 mm external dimensions
310 x 170 x 170 mm internal dimensions
10 liters
3 Velcro fasteners 40 mm wide for attachment to the luggage rack from below
2 Velcro fasteners for attachment to the luggage rack to the front (seat)
Outlet for the discharge cable with rubber coating to prevent moistureingress
waterproof cover to protect against rain
Shoulder strap detachable (included)
Reflective strips on 2 sides for safe driving.
Up to 5 kg weight
Own weight: 545 grams
Technical Specifications of the battery:
Li-ion cell: INR21700-M50T
Voltage (nominal): 36V
Capacity: 15Ah
Energy: approx. 540 Wh
Configuration: 10S3P
Construction: 10 x 3
Internal resistance: < 75 mOhm
Charging voltage: 42V
End-of-discharge voltage: 30V
Continuous discharge current: 20A = 720 watts
10 min discharge current: 25A = 900 watts
5 seconds discharge current: 35A = about 1250 watts
Weight: Approx. 2.5 kg.
Battery dimensions:
Length: 235mm
Width: 70-85mm
Height: 75mm
ENERpower softpack battery 36V 15Ah for eBikes, with INR21700-50E battery cells from Samsung SDI in Enerprof frame bag
Important General Information
This 36V e-bike battery in softpack is manufactured for insertion in carrier bag . With this bike-frame bag, you can attach the battery to the frame of the eBike and ideally connect it to a mid-sized engine. The frame bag is waterproof and with the separation between charging and discharging cables you don’t have to overplug constantly.
The battery cells are assembled in a plastic holder and equipped with a ENERpower branded BMS 20A-22A. The charging is done with a spiral cable (20-100 cm extendable) with an XLR-3-pin connector. Discharging is done via a discharge cable with XT90 connector (male). A counterpart XT90 is also included.
A safety fuse of 30A in a waterproof mount limits the power consumption and provides an additional safety measure.
This battery is also suitable for engines with up to 750 watts of power.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
Battery – Highlights
High-quality manufacturing – made in Germany
Assembly just-in-time
BMS with integrated passive balancer (4.1V pro rechargeable cell)
BMS with protection against overcharge, deep discharge, over-discharge (temperature monitoring)
Assembly with Samsung SDI, Panasonic (Sanyo) or LG Chem cells (subject to availability)
directly from the manufacturer
Rechargeable – After 300 charging cycles maintains 80% of the original capacity
No memory effect – charge the battery whenever you want
Environmentally friendly according to EU Directive 2002/95/EC (RoHS)
Battery – Technical Data
Li-ion Cell: Samsung SDI INR21700-50E
Voltage (nominal): 36V (37V)
Capacity: 15Ah
Power: about 540Wh
Configuration: 10S3P
Internal resistance: < 75 mOhm
Charge Voltage: 42V
Maximum Charging current: 5A
End-of-Discharge Voltage: 30V
Continuous Discharge Current: 20A = 720 watts
10 seconds 30A: approx. 1080 watts
Weight: approx. 2.5Kg. (Battery only)
The Enerpower frame bag is a collaboration between Enerdan and Roswheel in order to better design the Attack frame bag for use with eBike batteries. The new frame bag is: • Waterproof • Has 5 x Velcro fasteners can be attached at any point • Can be opened in 240 degrees • Suitable as a frame bag for batteries up to 5 kg. • Is approx. 350 mm long, approx. 130 mm high and 90 mm wide • Fits batteries made with 21700 format battery cells. • Has a larger opening for charging and discharging cables
Compatibility
Compatible with engines 250 watts / 500 watts / 750 watts
ENERpower Softpack battery 36V in format 10S4P RECTANGULAR | 600 Wh | capacity 16 Ah | for Pedelecs, eBikes DIY | with Samsung SDI INR21700-40T
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 750 watts / 950 Watt / 1080 Watt / 1440 Watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: Samsung SDI INR21700-40T
Voltage (nominal): 36V (37V)
Capacity: 16 Ah
Power: approx. 600 Wh
Configuration: 10S4P (set up: 10x4 - rectangular)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Charge Max.: 8A
Continuous discharge Current: 40A = 1440 watts
5 seconds discharge current: 50A = 1800 watts
Weight: approx. 3 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 230 mm
Width: 92mm – 120 mm
Height: 74 mm
ENERpower softpack battery 36V 16Ah / 20Ah Ah for eBikes in Enerprof frame bag
Important General Information
This 36V e-bike battery in softpack is manufactured for insertion in carrier bag . With this bike-frame bag, you can attach the battery to the frame of the eBike and ideally connect it to a mid-sized engine. The frame bag is waterproof and with the separation between charging and discharging cables you don’t have to overplug constantly.
The battery cells are assembled in a plastic holder and equipped with a ENERpower branded Smart BMS 30A. The charging is done with a spiral cable (20-100 cm extendable) with an XLR-3-pin connector. Discharging is done via a discharge cable with XT90 connector (male). A counterpart XT90 is also included.
This battery is also suitable for engines with up to 1080 watts of power.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
Battery – Highlights
High-quality manufacturing – made in Germany
Assembly just-in-time
Smart BMS with integrated passive balancer (4.1V pro rechargeable cell)
Smart BMS with protection against overcharge, deep discharge, over-discharge (temperature monitoring)
Assembly with Samsung SDI, Panasonic (Sanyo) or LG Chem cells (subject to availability)
directly from the manufacturer
Rechargeable – After 300 charging cycles maintains 80% of the original capacity
No memory effect – charge the battery whenever you want
Environmentally friendly according to EU Directive 2002/95/EC (RoHS)
Battery – Technical Data
Li-ion Cell: M50T / 40T
Voltage (nominal): 36V (37V)
Capacity: 16Ah / 20Ah
Power: about 580Wh - 720Wh
Configuration: 10S4P
Internal resistance: < 75 mOhm
Charge Voltage: 42V
Maximum Charging current: 8A
End-of-Discharge Voltage: 30V
Continuous Discharge Current: 30A = 1080watts
Weight: approx. 3.2Kg. (Battery only)
The Enerpower frame bag is a collaboration between Enerdan and Roswheel in order to better design the Attack frame bag for use with eBike batteries. The new frame bag is: • Waterproof • Has 5 x Velcro fasteners can be attached at any point • Can be opened in 240 degrees • Suitable as a frame bag for batteries up to 5 kg. • Is approx. 350 mm long, approx. 130 mm high and 90 mm wide • Fits batteries made with 21700 format battery cells. • Has a larger opening for charging and discharging cables
Compatibility
Compatible with engines 250 watts / 500 watts / 750 watts
ENERpower Softpack battery 36V in format 10S6P square | 615 Wh | capacity 17.1 Ah | for Pedelecs, eBikes DIY |
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 750 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: Samsung INR18650-29E
Voltage (nominal): 36V (37V)
Capacity: 17.1 Ah
Power: approx. 615 Wh
Configuration: 10S6P (set up: 10x6)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Charge Max.: 5A
Continuous discharge Current: 20A = 720 watts
5 seconds discharge current: 30A = 1080 watts
Weight: approx. 3.25 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90, XT-60, Anderson
Dimensions
Length: 200 mm
Width: 120 mm – 130 mm
Height: 65-68 mm
ENERpower Softpack battery 36V in format 10S6P square | 615 Wh | capacity 17.1 Ah | for Pedelecs, eBikes DIY |
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 750 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: Samsung INR18650-29E
Voltage (nominal): 36V (37V)
Capacity: 17.1 Ah
Power: approx. 615 Wh
Configuration: 10S6P (set up: 10x6)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Charge Max.: 5A
Continuous discharge Current: 30A = 1080 watts
5 seconds discharge current: 35A = 1250 watts
Weight: approx. 3.25 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90, XT-60, Anderson
Dimensions
Length: 200 mm
Width: 120 mm – 130 mm
Height: 65-68 mm
ENERpower Softpack battery 36V in format 10S6P square | 725 Wh | capacity 19.2 Ah | for Pedelecs, eBikes DIY | with MH1.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
30A BMS: 250 watts up to 1080 Watt
40A BMS: 250 watts up to 1440 Watt
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: LG Chem INR18650-MH1
Voltage (nominal): 36V (37V)
Capacity: 19.2 Ah
Power: approx. 705 Wh
Configuration: 10S6P (set up: 10x6)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Charge Max.: 8A
Continuous discharge Current: 30A = 1080 watts
5 seconds discharge current: 35A = 1260 watts
Weight: approx. 3.25 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 200 mm
Width: 120 mm – 130 mm
Height: 65-68 mm
ENERpower Softpack battery 36V in format 10S5P RECTANGULAR | 740Wh | capacity 20Ah | for Pedelecs, eBikes DIY | with Samsung SDI INR21700-40T
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 750 watts / 950 Watt / 1080 Watt / 1440 Watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: Samsung SDI INR21700-40T
Voltage (nominal): 36V (37V)
Capacity: 20 Ah
Power: approx. 740 Wh
Configuration: 10S5P (set up: 10x5- rectangular)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Charge Max.: 8A
Continuous discharge Current: 40A = 1440 watts
5 seconds discharge current: 50A = 1800 watts
Weight: approx. 3.7 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 230 mm
Width: 115mm – 140 mm
Height: 74 mm
ENERpower Softpack battery 36V, format 10S4P | 720 Wh | capacity 20 Ah | for Pedelecs, eBikes DIY | INR21700-50E.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 7 cells are used on the longest side (around 165 mm). We manufacture this type of battery in the format 10S4P (construction 7×6)
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 540 watts / 750 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
With battery cells INR21700-50E
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: INR21700-50E
Voltage (nominal): 36V (37V)
Capacity: 20 Ah
Power: approx. 720 Wh
Configuration: 10S4P (set up: 7×6 - Square)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Maximal charge current: 5A
Continuous discharge Current: 20A = 720 watts
10 minutes discharge Current: 25A = 900 watts
Weight: 3.1 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90 / XT-60 / Anderson
Dimensions
Length: 235 mm
Width: 100 mm – 110 mm
Height: 71 mm
ENERpower Softpack battery 36V, format 10S4P SQUARE | 720 Wh | capacity 20 Ah | for Pedelecs, eBikes DIY | INR21700-50E.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 7 cells are used on the longest side (around 165 mm). We manufacture this type of battery in the format 10S4P (construction 7×6)
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 540 watts / 750 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
With battery cells INR21700-50E
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: INR21700-50E
Voltage (nominal): 36V (37V)
Capacity: 20 Ah
Power: approx. 720 Wh
Configuration: 10S4P (set up: 7×6 - Square)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Maximal charge current: 5A
Continuous discharge Current: 20A = 720 watts
10 minutes discharge Current: 25A = 900 watts
5 seconds discharge current: 35A = 1260 watts
Continuous load per cell: approx. 4A or approx. 8A at peak load
Weight: 3.1 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 165 mm
Width: 140 mm – 155 mm
Height: 71 mm
ENERpower Softpack battery 36V, format 10S4P RECTANGULAR | 720 Wh | capacity 20 Ah | for Pedelecs, eBikes DIY | Samsung SDI INR21700-50E.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 540 watts / 750 watts / 1080 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: Samsung SDI INR21700-50E
Voltage (nominal): 36V (37V)
Capacity: 20 Ah
Power: approx. 720 Wh
Configuration: 10S4P (set up: 10×4 - rectangular)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Maximal charge current: 8A
Continuous discharge Current: 30A = 1080 watts
5 seconds discharge current: 50A = 1800 watts
Weight: 3.1 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90 / XT-60 / Anderson PowerPole
Dimensions
Length: 220 mm
Width: 94 mm – 1110 mm
Height: 71 mm
ENERpower Softpack battery 36V, format 10S4P RECTANGULAR | 720 Wh | capacity 20 Ah | for Pedelecs, eBikes DIY | Samsung SDI INR21700-50E.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 540 watts / 750 watts / 1080 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: Samsung SDI INR21700-50E
Voltage (nominal): 36V (37V)
Capacity: 20 Ah
Power: approx. 720 Wh
Configuration: 10S4P (set up: 10×4 - rectangular)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Maximal charge current: 8A
Continuous discharge Current: 30A = 1080 watts
5 seconds discharge current: 50A = 1800 watts
Weight: 3.1 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90 / XT-60 / Anderson PowerPole
Dimensions
Length: 220 mm
Width: 94 mm – 1110 mm
Height: 71 mm
ENERpower softpack battery 36V 20Ah for eBikes, with INR21700-M50T battery cells from LG Chem INR21700-M50T in Enerprof frame bag
Important General Information
This 36V e-bike battery in softpack is manufactured for insertion in carrier bag . With this bike-frame bag, you can attach the battery to the frame of the eBike and ideally connect it to a mid-sized engine. The frame bag is waterproof and with the separation between charging and discharging cables you don’t have to overplug constantly.
The battery cells are assembled in a plastic holder and equipped with a ENERpower branded BMS 20A-22A. The charging is done with a spiral cable (20-100 cm extendable) with an XLR-3-pin connector. Discharging is done via a discharge cable with XT90 connector (male). A counterpart XT90 is also included.
A safety fuse of 30A in a waterproof mount limits the power consumption and provides an additional safety measure.
This battery is also suitable for engines with up to 750 watts of power.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
Battery – Highlights
High-quality manufacturing – made in Germany
Assembly just-in-time
BMS with integrated passive balancer (4.1V pro rechargeable cell)
BMS with protection against overcharge, deep discharge, over-discharge (temperature monitoring)
Assembly with Samsung SDI, Panasonic (Sanyo) or LG Chem cells (subject to availability)
directly from the manufacturer
Rechargeable – After 300 charging cycles maintains 80% of the original capacity
No memory effect – charge the battery whenever you want
Environmentally friendly according to EU Directive 2002/95/EC (RoHS)
Battery – Technical Data
Li-ion Cell: LG Chem INR21700-M50T
Voltage (nominal): 36V (37V)
Capacity: 20Ah
Power: about 720Wh
Configuration: 10S2P - 10S5P
Internal resistance: < 75 mOhm
Charge Voltage: 42V
Maximum Charging current: 5A
End-of-Discharge Voltage: 30V
Continuous Discharge Current: 20A = 720 watts
10 seconds 30A: approx. 1080 watts
Weight: approx. 2.7Kg. (Battery only)
The Enerpower frame bag is a collaboration between Enerdan and Roswheel in order to better design the Attack frame bag for use with eBike batteries. The new frame bag is: • Waterproof • Has 5 x Velcro fasteners can be attached at any point • Can be opened in 240 degrees • Suitable as a frame bag for batteries up to 5 kg. • Is approx. 350 mm long, approx. 130 mm high and 90 mm wide • Fits batteries made with 21700 format battery cells. • Has a larger opening for charging and discharging cables
Compatibility
Compatible with engines 250 watts / 500 watts / 750 watts