ENERpower softpack battery 36V | Format 10S14P | Energy 2600Wh | Capacity 70Ah | for industrial machines, pedelecs, eBikes, eRickshaws, electric cargo bikes, electric boats DIY | with LG Chem INR21700-M50TL | For consumers with a power of up to 1800 watts
General Information
This battery is assembled on 2 levels. The battery is approx. 250 x 150 x 160 mm and weighs approx. 10.70 kg. We can manufacture the battery with and without a charge level indicator and can be offered with a cable for charging and discharging, or with 2 separate cables
Smart BMS (Battery Management System)
This battery is manufactured with a Smart BMS with 50A continuous load (for 36V consumers with up to 1800 watts of power). A Smart BMS is digitally programmed and controlled in comparison to an analog BMS. The monitoring of voltage (overcharge and deep discharge), current (overdischarge) and temperature are more accurate. A Bluetooth is integrated in this battery, with which the data can be called up via an app
scope of application
We have developed this series of batteries for light electric vehicles such as electric rickshaws, electric cargo bikes, but also for robots, machines and electric boat motors
Compatible with 36V motors 250 watts / 500 watts / 750 watts / 1200 watts / 1500 watts / 1800 watts
Highlights
High quality production - Made in Germany
Just-in-time manufacturing
Smart BMS with an integrated passive balancer
Direct from the manufacturer
Rechargeable - Still 80% of original capacity after 500 charge cycles
No memory effect - charge the battery whenever you want
Environmentally friendly according to EU directive 2002/95 / EG (RoHS)
Technical specifications Li-ion cell: LG Chem INR21700-M50TL Voltage (nominal): 36V (37V) Capacity: 70Ah Energy: approx. 2600 Wh Configuration: 10S14P Charging voltage: 42V End-of-discharge voltage: 30V Charging Current (Max.): 20A Continuous discharge current: 50A = 1800 watts Weight: approx. 10.70 kg. Dimensions: 250 x 150 x 160 mm Load: XT-60, XT-90, Anderson, or Weipu Discharge connector: XT-60, or XT-90
ENERpower Softpack battery 36V, format 10S2P rectangular | for Pedelecs, eBikes DIY | Super Drain
Important General Information
We manufacture a range of Super Drain batteries in softpacks in Berlin. These batteries are small in size and weight and are made with high-current INR21700-40T or INR21700-50S battery cells. The Smart BMS (Battery Management System) with a continuous load capacity of 30A is always mounted on the longest side of the battery, resulting in an approximately 20mm thicker section at that point.
This battery is designed for users who typically complete short and demanding distances, as well as for situations where overall weight plays a crucial role (off-road, inclines, etc.).
The batteries are manufactured in a 36V (10S) configuration, with options available in a 5x4 or 10x2 setup.
The softpack batteries are constructed with FR4 insulation, which is a flame-resistant and fire-retardant composite material consisting of epoxy resin and fiberglass fabric. FR-4 is commonly used as an electrically non-conductive substrate in printed circuit boards.
Additionally, this battery features an LED status indicator located on the top side of the battery. The indicator displays the battery's charge level in the following steps: "Empty," "25%," "50%," "75%," and "Full."
Compatible with 36V motors
Up to 1080 Watt
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: INR21700-40T, or INR21700-50S
Voltage (nominal): 36V (37V)
Capacity: 8Ah / 10 Ah
Power: approx. 288 Wh / 360 Wh
Configuration: 10S2P (set up: 10×2)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Continuous discharge Current: 30A = 1080 watts
Charging Current (Max): 8A
Weight: 1.6 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90 / XT-60
Dimensions
Length: 235 mm
Width: 50 mm – 70 mm
Height: 72 mm
ENERpower Softpack battery 36V, format 10S2P rectangular | 360 Wh | capacity 10 Ah | for Pedelecs, eBikes DIY | LG Chem M50.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 Watts / 500 Watts / 540 Watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
With battery cells INR21700-M50 from LG Chem
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: LG Chem INR21700-M50
Voltage (nominal): 36V (37V)
Capacity: 10 Ah
Power: approx. 360 Wh
Configuration: 10S2P (set up: 10×2)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Continuous discharge Current: 15A = 720 watts
10 minutes discharge Current: 20A = 900 watts
5 seconds discharge current: 25A = 1080 watts
Weight: 1.6 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 220 mm
Width: 44 mm – 56 mm
Height: 72 mm
ENERpower Softpack battery 36V, format 10S2P, square) | 360 Wh | capacity 10 Ah | for Pedelecs, eBikes DIY | LG Chem M50.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 540 watts / 700 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
With battery cells INR21700-M50 from LG Chem
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: INR21700-M50 from LG Chem
Voltage (nominal): 36V (37V)
Capacity: 10 Ah
Power: approx. 360 Wh
Configuration: 10S2P (set up: 5x4)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Continuous discharge Current: 15A = 720 watts
10 minutes discharge Current: 20A = 900 watts
5 seconds discharge current: 25A = 1080 watts
Weight: 1.6 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 110 mm
Width: 88 mm – 100 mm
Height: 72 mm
ENERpower Softpack battery 36V in format 10S3P RECTANGULAR | 435Wh | capacity 12 Ah | for Pedelecs, eBikes DIY | with Samsung SDI INR21700-40T
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
A smart BMS is digitally controlled and therefore more accurate. The BMS reads more powerfully and also supports recuperation.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 750 watts / 950 Watt / 1080 Watt / 1440 Watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: Samsung SDI INR21700-40T
Voltage (nominal): 36V (37V)
Capacity: 12 Ah
Power: approx. 435 Wh
Configuration: 10S3P (set up: 10x3 - rectangular)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Charge Max.: 8A
Continuous discharge Current: 30A = 1080 Watt or 40A = 1440 watts
5 seconds discharge current: 50A = 1800 watts
Weight: approx. 2.5 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 230 mm
Width: 70mm – 90 mm
Height: 74 mm
ENERpower Softpack battery 36V in format 10S3P square | 540 Wh | capacity 15 Ah | for Pedelecs, eBikes DIY | with Samsung 50E.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 750 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
With battery cells INR18650-35E from Samsung SDI
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: Samsung INR18650-50E
Voltage (nominal): 36V (37V)
Capacity: 15 Ah
Power: approx. 540 Wh
Configuration: 10S3P (set up: 6x5)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Continuous discharge Current: 20A = 720 watts
10 minutes discharge Current: 25A = 900 watts
5 seconds discharge current: 30A = 1040 watts
Continuous load per battery cell: approx. 3.7A and approx. 7A in peak load
Weight: approx. 2.5 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90 / XT-60 / Anderson
Dimensions
Length: 140 mm
Width: 115 mm – 125 mm
Height: 74 mm
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 540 watts / 750 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
With battery cells INR21700-M50 from LG Chem
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: LG Chem INR21700-M50
Voltage (nominal): 36V (37V)
Capacity: 15 Ah
Power: approx. 540 Wh
Configuration: 10S3P (set up: 10×3 - rectangular)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Maximal charge current: 5A
Continuous discharge Current: 20A = 720 watts
10 minutes discharge Current: 25A = 900 watts
5 seconds discharge current: 35A = 1260 watts
Continuous load per cell: approx. 4A or approx. 8A at peak load
Weight: 2.5 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 220 mm
Width: 69 mm – 80 mm
Height: 71 mm
ENERpower Softpack battery 36V, format 10S5P, RECTANGULAR | 580 Wh | capacity 16 Ah | for Pedelecs, eBikes DIY | LG Chem INR18650-MH1.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 Watts / 500 Watts / 540 Watts / 720 Watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: LG Chem INR18650-MH1
Voltage (nominal): 36V (37V)
Capacity: 16 Ah
Power: approx. 580Wh
Configuration: 10S5P (set up: 10x5)
Internal resistance: < 75 mOhm
Charge Voltage: 42V
End-of-Discharge Voltage: 30V
Continuous discharge current: 20A = 720 Watt
10 Min. discharge current: 25A = 900 Watt
5 Sec. discharge current: 30A = 1100Watt
Weight: 2.8 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90 / XT-60 / Anderson
Dimensions
Length: 210 mm
Width: 110 mm – 125 mm
Height: 70 mm
ENERpower Softpack battery 36V in format 10S4P RECTANGULAR | 600 Wh | capacity 16 Ah | for Pedelecs, eBikes DIY | with Samsung SDI INR21700-40T
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 750 watts / 950 Watt / 1080 Watt / 1440 Watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: Samsung SDI INR21700-40T
Voltage (nominal): 36V (37V)
Capacity: 16 Ah
Power: approx. 600 Wh
Configuration: 10S4P (set up: 10x4 - rectangular)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Charge Max.: 8A
Continuous discharge Current: 40A = 1440 watts
5 seconds discharge current: 50A = 1800 watts
Weight: approx. 3 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 230 mm
Width: 92mm – 120 mm
Height: 74 mm
ENERpower Softpack battery 36V in format 10S6P square | 615 Wh | capacity 17.1 Ah | for Pedelecs, eBikes DIY |
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 750 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: Samsung INR18650-29E
Voltage (nominal): 36V (37V)
Capacity: 17.1 Ah
Power: approx. 615 Wh
Configuration: 10S6P (set up: 10x6)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Charge Max.: 5A
Continuous discharge Current: 20A = 720 watts
5 seconds discharge current: 30A = 1080 watts
Weight: approx. 3.25 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90, XT-60, Anderson
Dimensions
Length: 200 mm
Width: 120 mm – 130 mm
Height: 65-68 mm
ENERpower Softpack battery 36V in format 10S6P square | 615 Wh | capacity 17.1 Ah | for Pedelecs, eBikes DIY |
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 750 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: Samsung INR18650-29E
Voltage (nominal): 36V (37V)
Capacity: 17.1 Ah
Power: approx. 615 Wh
Configuration: 10S6P (set up: 10x6)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Charge Max.: 5A
Continuous discharge Current: 30A = 1080 watts
5 seconds discharge current: 35A = 1250 watts
Weight: approx. 3.25 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90, XT-60, Anderson
Dimensions
Length: 200 mm
Width: 120 mm – 130 mm
Height: 65-68 mm
ENERpower Softpack battery 36V in format 10S6P square | 725 Wh | capacity 19.2 Ah | for Pedelecs, eBikes DIY | with MH1.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
30A BMS: 250 watts up to 1080 Watt
40A BMS: 250 watts up to 1440 Watt
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: LG Chem INR18650-MH1
Voltage (nominal): 36V (37V)
Capacity: 19.2 Ah
Power: approx. 705 Wh
Configuration: 10S6P (set up: 10x6)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Charge Max.: 8A
Continuous discharge Current: 30A = 1080 watts
5 seconds discharge current: 35A = 1260 watts
Weight: approx. 3.25 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 200 mm
Width: 120 mm – 130 mm
Height: 65-68 mm
ENERpower Softpack battery 36V in format 10S5P RECTANGULAR | 740Wh | capacity 20Ah | for Pedelecs, eBikes DIY | with Samsung SDI INR21700-40T
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 750 watts / 950 Watt / 1080 Watt / 1440 Watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: Samsung SDI INR21700-40T
Voltage (nominal): 36V (37V)
Capacity: 20 Ah
Power: approx. 740 Wh
Configuration: 10S5P (set up: 10x5- rectangular)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Charge Max.: 8A
Continuous discharge Current: 40A = 1440 watts
5 seconds discharge current: 50A = 1800 watts
Weight: approx. 3.7 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 230 mm
Width: 115mm – 140 mm
Height: 74 mm
ENERpower Softpack battery 36V, format 10S4P | 720 Wh | capacity 20 Ah | for Pedelecs, eBikes DIY | INR21700-50E.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 7 cells are used on the longest side (around 165 mm). We manufacture this type of battery in the format 10S4P (construction 7×6)
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 540 watts / 750 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
With battery cells INR21700-50E
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: INR21700-50E
Voltage (nominal): 36V (37V)
Capacity: 20 Ah
Power: approx. 720 Wh
Configuration: 10S4P (set up: 7×6 - Square)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Maximal charge current: 5A
Continuous discharge Current: 20A = 720 watts
10 minutes discharge Current: 25A = 900 watts
Weight: 3.1 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90 / XT-60 / Anderson
Dimensions
Length: 235 mm
Width: 100 mm – 110 mm
Height: 71 mm
ENERpower Softpack battery 36V, format 10S4P SQUARE | 720 Wh | capacity 20 Ah | for Pedelecs, eBikes DIY | INR21700-50E.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 7 cells are used on the longest side (around 165 mm). We manufacture this type of battery in the format 10S4P (construction 7×6)
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 540 watts / 750 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
With battery cells INR21700-50E
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: INR21700-50E
Voltage (nominal): 36V (37V)
Capacity: 20 Ah
Power: approx. 720 Wh
Configuration: 10S4P (set up: 7×6 - Square)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Maximal charge current: 5A
Continuous discharge Current: 20A = 720 watts
10 minutes discharge Current: 25A = 900 watts
5 seconds discharge current: 35A = 1260 watts
Continuous load per cell: approx. 4A or approx. 8A at peak load
Weight: 3.1 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 165 mm
Width: 140 mm – 155 mm
Height: 71 mm
ENERpower Softpack battery 36V, format 10S4P RECTANGULAR | 720 Wh | capacity 20 Ah | for Pedelecs, eBikes DIY | Samsung SDI INR21700-50E.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 540 watts / 750 watts / 1080 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: Samsung SDI INR21700-50E
Voltage (nominal): 36V (37V)
Capacity: 20 Ah
Power: approx. 720 Wh
Configuration: 10S4P (set up: 10×4 - rectangular)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Maximal charge current: 8A
Continuous discharge Current: 30A = 1080 watts
5 seconds discharge current: 50A = 1800 watts
Weight: 3.1 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90 / XT-60 / Anderson PowerPole
Dimensions
Length: 220 mm
Width: 94 mm – 1110 mm
Height: 71 mm
ENERpower Softpack battery 36V, format 10S5P RECTANGULAR | 910 Wh | capacity 25 Ah | for Pedelecs, eBikes DIY | Samsung SDI INR21700-50E.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 540 watts / 750 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: Samsung SDI INR21700-50E
Voltage (nominal): 36V (37V)
Capacity: 25 Ah
Power: approx. 910 Wh
Configuration: 10S5P (set up: 10×5 - rectangular)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Maximal charge current: 5A
Continuous discharge Current: 20A = 720 watts
10 minutes discharge Current: 25A = 900 watts
5 seconds discharge current: 35A = 1260 watts
Continuous load per cell: approx. 4A or approx. 8A at peak load
Weight: 3.8 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 230 mm
Width: 115 mm – 125 mm
Height: 75 mm
ENERpower Softpack battery 36V, format 10S5P SQUARE | 910 Wh | capacity 25 Ah | for Pedelecs, eBikes DIY | LG Chem M50.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 540 watts / 750 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
With battery cells INR21700-M50 from LG Chem
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: LG Chem INR21700-M50
Voltage (nominal): 36V (37V)
Capacity: 25 Ah
Power: approx. 910 Wh
Configuration: 10S5P (set up: 8x7 - square)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Maximal charge current: 5A
Continuous discharge Current: 20A = 720 watts
10 minutes discharge Current: 25A = 900 watts
5 seconds discharge current: 35A = 1260 watts
Continuous load per cell: approx. 4A or approx. 8A at peak load
Weight: 3.8 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 176 mm
Width: 132 mm – 142 mm
Height: 75 mm