ENERpower Softpack battery 36V, format 10S2P, square) | 360 Wh | capacity 10 Ah | for Pedelecs, eBikes DIY | LG Chem M50.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 540 watts / 700 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
With battery cells INR21700-M50 from LG Chem
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: INR21700-M50 from LG Chem
Voltage (nominal): 36V (37V)
Capacity: 10 Ah
Power: approx. 360 Wh
Configuration: 10S2P (set up: 5x4)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Continuous discharge Current: 15A = 720 watts
10 minutes discharge Current: 20A = 900 watts
5 seconds discharge current: 25A = 1080 watts
Weight: 1.6 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 110 mm
Width: 88 mm – 100 mm
Height: 72 mm
ENERpower Softpack battery 36V, format 10S2P rectangular | 360 Wh | capacity 10 Ah | for Pedelecs, eBikes DIY | LG Chem M50T.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 Watts / 500 Watts / 540 Watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
With battery cells INR21700-M50 from LG Chem
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: LG Chem INR21700-M50
Voltage (nominal): 36V (37V)
Capacity: 10 Ah
Power: approx. 360 Wh
Configuration: 10S2P (set up: 10×2)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Continuous discharge Current: 15A = 720 watts
10 minutes discharge Current: 20A = 900 watts
5 seconds discharge current: 25A = 1080 watts
Weight: 1.6 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 220 mm
Width: 44 mm – 56 mm
Height: 72 mm
ENERpower Softpack battery 36V in format 10S3P RECTANGULAR | 435Wh | capacity 12 Ah | for Pedelecs, eBikes DIY | with Samsung SDI INR21700-40T
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
A smart BMS is digitally controlled and therefore more accurate. The BMS reads more powerfully and also supports recuperation.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 750 watts / 950 Watt / 1080 Watt / 1440 Watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: Samsung SDI INR21700-40T
Voltage (nominal): 36V (37V)
Capacity: 12 Ah
Power: approx. 435 Wh
Configuration: 10S3P (set up: 10x3 - rectangular)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Charge Max.: 8A
Continuous discharge Current: 30A = 1080 Watt or 40A = 1440 watts
5 seconds discharge current: 50A = 1800 watts
Weight: approx. 2.5 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 230 mm
Width: 70mm – 90 mm
Height: 74 mm
ENERpower Softpack battery 36V in format 10S6P square | 725 Wh | capacity 19.2 Ah | for Pedelecs, eBikes DIY | with MH1.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
30A BMS: 250 watts up to 1080 Watt
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: LG Chem INR18650-MH1
Voltage (nominal): 36V (37V)
Capacity: 19.2 Ah
Power: approx. 705 Wh
Configuration: 10S6P (set up: 10x6)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Charge Max.: 8A
Continuous discharge Current: 30A = 1080 watts
Weight: approx. 3.25 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 210 mm
Width: 120 mm – 130 mm
Height: 65-68 mm
ENERpower Softpack battery 36V, format 10S5P RECTANGULAR | 910 Wh | capacity 25 Ah | for Pedelecs, eBikes DIY | Samsung SDI INR21700-50E.
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 540 watts / 750 watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: Samsung SDI INR21700-50E
Voltage (nominal): 36V (37V)
Capacity: 25 Ah
Power: approx. 910 Wh
Configuration: 10S5P (set up: 10×5 - rectangular)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Maximal charge current: 5A
Continuous discharge Current: 20A = 720 watts
10 minutes discharge Current: 25A = 900 watts
5 seconds discharge current: 35A = 1260 watts
Continuous load per cell: approx. 4A or approx. 8A at peak load
Weight: 3.8 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 230 mm
Width: 115 mm – 125 mm
Height: 75 mm
ENERpower Softpack battery 36V in format 10S7P RECTANGULAR | 1440 Wh | capacity 40 Ah | for Pedelecs, eBikes DIY | with INR21700-M50T
Important General Information
The 36V batteries in softpack, which we manufacture in Berlin, have 2 versions square and rectangular. The batteries are manufactured in plastic cell brackets. Charging is done with a high-quality spiral cable (20 cm – 100 cm) with an XLR-3 PINS, discharging via a discharge cable with XT90 connector (male). A fuse of 30A in a water-resistant holder limits the current drain.
In the square version, 8 cells are used on the longest side (160 mm). We manufacture this type of battery in the formats 10S3P (construction 8×4), 10S4P (construction 8×5), 10S5P (construction 8×7) and 10S6P (construction 8×8).
In the rectangular version, 10 cells are used on the longest side (200 mm). We assemble this type of battery in the formats 10S2P (construction 10×2), 10S3P (10×3), 10S4P (10×4), 10S5P (10×5) and 10S6P (10×6).
The Battery Management System (BMS) is always mounted on the longest side of the battery. At this side the battery is approx. 10 -15 mm thicker.
We manufacture the Softpack batteries with FR4 insulation, flame retardant composites made of epoxy resin and glass fabrics. FR-4 is used, among other things, as an electrically non-conductive carrier material for electrical circuit boards.
In this battery we have an LED charge status display (empty/25%/50%/75%/full). This is located on the upper side of the battery
Compatible with 36V motors
250 watts / 500 watts / 750 watts / 950 Watt / 1080 Watt / 1440 Watts
Highlights
High-quality production - Made in Germany
Production Just-In-Time
BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring)
Direct from the manufacturer
Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity
No memory effect - charge the battery whenever you want
Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS)
Technical Specifications
Li-ion Cell: LG Chem INR21700-M50T
Voltage (nominal): 36V (37V)
Capacity: 40 Ah
Power: approx. 1440 Wh
Configuration: 10S8P (set up: 10x8 - rectangular)
Internal resistance: < 75 mOhm
Charge voltage: 42V
End-of-discharge voltage: 30V
Charge Max.: 8A
Continuous discharge Current: 40A = 1440 watts
5 seconds discharge current: 50A = 1800 watts
Weight: approx. 5.8 Kg.
Charge connector (connects to the charger): XLR-3 (3 pins)
Discharge connector (connects to the motor): XT-90
Dimensions
Length: 235 mm
Width: 185 mm – 195 mm
Height: 72 mm