ENERpower battery LiFePO4 24V (25.6V) for the operation of 24V devices, motors, wheel chairs etc. Important general informationWe assemble this series of LiFePo4 batteries in the 8S (25.6V) format with battery cells from Haidi. All battery cells have important safety certifications such as UL and IECOur batteries are light (compared to lead acid batteries) and can reach up to 2000 charging cycles.The batteries are manufactured with 2 outputs (charging / discharging). For charging (up to 8A charging current) we use an XLR-3 connector. For unloading you can choose between XT-60, XT-90 or Anderson PowerPoleYou can purchase the battery with 2 different BMS's:1. Up to 15A continuous load - for devices with a consumption of up to 370 watts2. Up to 30A continuous load - for devices with a consumption of up to 740 wattsThe protection against overcharging (29.4V) and against deep discharge (16V) avoids damage to the battery and increases the safety factor.We manufacture these batteries with a charge status indicator so that you can see the charge status of the battery at any time. highlights High-quality production in Germany BMS with an integrated passive balancer BMS with protection against overcharging, deep discharging, overdischarging (temperature monitoring) Direct from the manufacturer Rechargeable - Still 80% of original capacity after 1800 full charge cycles No memory effect - charge the battery whenever you want Environmentally friendly according to EU directive 2002/95/EG (RoHS) Technical specifications  Voltage (nominal): 24V (25.6V) Capacity: 28Ah Configuration: 8S7P Energy: about 717Wh Maximum charging current: 8A Internal resistance: < 70mOhm Charging voltage: 29.2V End-of-discharge voltage: 16V Weight: approx. 5.2 kg. Charging: XLR-3 Discharge: XT-60 / XT-90 / Anderson PowerPole Dimensions: ca. 225 x 200 x 70 mm

ENERpower battery case 24V in format 7S12P | 1000Wh | capacity 40Ah | for Pedelecs, eBikes, Maschines, Drones, Industry, DIY | with Panasonic NCR2070C General Information . The battery in Case is assembled with NCR2070C Li-Ion battery cells from Panasonic is controlled by a 40A Smart BMS (Battery Management System). This battery is suitable for 24V electric motors, or devices with a total output of up to 750 watts consumption A charge level indicator shows at any time in percent how full (or empty) the battery is. In this battery system we have a Weipu Bayonet IP67 connector for charging (up to 30A) and an Anderson high-current connector for discharging with an on/off switch you can easily connect the power supply without disconnecting the battery from the consumer.On / off switchThe batteries can be easily switched on and off using a switchBMS (Battery Management System)This series of batteries is manufactured with a Smart BMS with 40A continuous load (for 24V motors up to 750 watts). A Smart BMS is digitally programmed and controlled in comparison to an analog BMS. Monitoring of voltage (overcharge and deep discharge), current (overdischarge) and temperature are more accurate. The passive balancer is also easier to control.scope of applicationWe have developed this series of batteries for light electric vehicles such as electric rickshaw, electric cargo bikes, electric boats, machines in the industrial sector etc.Compatible with 24V motorsUp to 750 WattsHighlights    High quality production - Made in Germany    Manufacturing just-in-time    Smart BMS with an integrated passive balancer    Direct from the manufacturer    Rechargeable - Still 80% of its original capacity after 500 charging cycles    No memory effect - charge the battery whenever you want    Environmentally friendly according to EU directive 2002/95 / EG (RoHS)Technical specifications    Li-ion cell: Panasonic NCR2070C    Voltage (nominal): 24V (25.2V - 25.9V)    Capacity: 40Ah    Energy: approx. 1000 Wh    Configuration: 7S12P    Charging voltage: 29.4V    Final discharge voltage: 21V    Charging current (max.): 20A    Continuous discharge current:30A = 750 Watts     Weight: approx.  6.55 Kg.    Dimensions: 390 x 285 x 120 mm    Charge: Weipu    Discharge connector: WEIPU  For more Information use please this link

ENERpower battery case 24V in format 7S11P | 1400Wh | capacity 55Ah | for Pedelecs, eBikes, Maschines, Drones, Industry, DIY | with LG Chem INR21700-M50T. General Information . The batteries are manufactured with  INR21700-M50T Li-Ion battery cells from LG Chem is controlled by a 60A Smart BMS (Battery Management System). This battery is suitable for 24V electric motors, or devices with a total output of up to 1500 watts. A charge level indicator shows at any time in percent how full (or empty) the battery is. In this battery system we have a Weipu Bayonet IP67 connector for charging (up to 30A) and an Anderson high-current connector for discharging with an on/off switch you can easily connect the power supply without disconnecting the battery from the consumer.On / off switchThe batteries can be easily switched on and off using a switchBMS (Battery Management System)This series of batteries is manufactured with a Smart BMS with 60A continuous load (for 24V motors up to 720 watts). A Smart BMS is digitally programmed and controlled in comparison to an analog BMS. Monitoring of voltage (overcharge and deep discharge), current (overdischarge) and temperature are more accurate. The passive balancer is also easier to control.scope of applicationWe have developed this series of batteries for light electric vehicles such as electric rickshaw, electric cargo bikes, electric boats, machines in the industrial sector etc.Compatible with 24V motors250 watts / 500 watts / 750 watts / 1000 Watts / 1250 Watts / 1500 WattsHighlights    High quality production - Made in Germany    Manufacturing just-in-time    Smart BMS with an integrated passive balancer    Direct from the manufacturer    Rechargeable - Still 80% of its original capacity after 500 charging cycles    No memory effect - charge the battery whenever you want    Environmentally friendly according to EU directive 2002/95 / EG (RoHS)Technical specifications    Li-ion cell: LG Chem INR21700-M50T    Voltage (nominal): 24V (25.2V - 25.9V)    Capacity: 55Ah    Energy: approx. 1400 Wh    Configuration: 7S11P    Charging voltage: 29.4V    Final discharge voltage: 21V    Charging current (max.): 20A    Continuous discharge current:30A = 750 Watts or 60A = 1500 Watts    Weight: approx.  8.85 Kg.    Dimensions: 390 x 293 x 172 mm    Charge: Weipu    Discharge connector: WEIPU, or Emphanol  For more Information use please this link

ENERpower battery case 24V in format 7S11P | 1600Wh | capacity 65Ah | for Pedelecs, eBikes, Maschines, Drones, Industry, DIY | with LG Chem INR21700-M50T. General Information . The batteries are manufactured with  INR21700-M50T Li-Ion battery cells from LG Chem is controlled by a 60A Smart BMS (Battery Management System). This battery is suitable for 24V electric motors, or devices with a total output of up to 1500 watts. A charge level indicator shows at any time in percent how full (or empty) the battery is. In this battery system we have a Weipu Bayonet IP67 connector for charging (up to 30A) and an Anderson high-current connector for discharging with an on/off switch you can easily connect the power supply without disconnecting the battery from the consumer.On / off switchThe batteries can be easily switched on and off using a switchBMS (Battery Management System)This series of batteries is manufactured with a Smart BMS with 60A continuous load (for 24V motors up to 720 watts). A Smart BMS is digitally programmed and controlled in comparison to an analog BMS. Monitoring of voltage (overcharge and deep discharge), current (overdischarge) and temperature are more accurate. The passive balancer is also easier to control.scope of applicationWe have developed this series of batteries for light electric vehicles such as electric rickshaw, electric cargo bikes, electric boats, machines in the industrial sector etc.Compatible with 24V motors250 watts / 500 watts / 750 watts / 1000 Watts / 1250 Watts / 1500 WattsHighlights    High quality production - Made in Germany    Manufacturing just-in-time    Smart BMS with an integrated passive balancer    Direct from the manufacturer    Rechargeable - Still 80% of its original capacity after 500 charging cycles    No memory effect - charge the battery whenever you want    Environmentally friendly according to EU directive 2002/95 / EG (RoHS)Technical specifications    Li-ion cell: LG Chem INR21700-M50T    Voltage (nominal): 24V (25.2V - 25.9V)    Capacity: 65Ah    Energy: approx. 1600 Wh    Configuration: 7S11P    Charging voltage: 29.4V    Final discharge voltage: 21V    Charging current (max.): 20A    Continuous discharge current:30A = 750 Watts or 60A = 1500 Watts    Weight: approx.  10.65 Kg.    Dimensions: 425 x 325 x 188 mm    Charge: Weipu    Discharge connector: WEIPU, or Emphanol  For more Information use please this link

ENERpower battery case 24V in format 7S20P | 2250Wh | capacity 100Ah | for Pedelecs, eBikes, Maschines, Drones, Industry, DIY | with LG Chem INR21700-M50T. General Information . The batteries are manufactured with  INR21700-M50T Li-Ion battery cells from LG Chem is controlled by a 60A Smart BMS (Battery Management System). This battery is suitable for 24V electric motors, or devices with a total output of up to 1500 watts. A charge level indicator shows at any time in percent how full (or empty) the battery is. In this battery system we have a Weipu Bayonet IP67 connector for charging (up to 30A) and an Anderson high-current connector for discharging with an on/off switch you can easily connect the power supply without disconnecting the battery from the consumer.On / off switchThe batteries can be easily switched on and off using a switchBMS (Battery Management System)This series of batteries is manufactured with a Smart BMS with 60A continuous load (for 24V motors up to 720 watts). A Smart BMS is digitally programmed and controlled in comparison to an analog BMS. Monitoring of voltage (overcharge and deep discharge), current (overdischarge) and temperature are more accurate. The passive balancer is also easier to control.scope of applicationWe have developed this series of batteries for light electric vehicles such as electric rickshaw, electric cargo bikes, electric boats, machines in the industrial sector etc.Compatible with 24V motors250 watts / 500 watts / 750 watts / 1000 Watts / 1250 Watts / 1500 WattsHighlights    High quality production - Made in Germany    Manufacturing just-in-time    Smart BMS with an integrated passive balancer    Direct from the manufacturer    Rechargeable - Still 80% of its original capacity after 500 charging cycles    No memory effect - charge the battery whenever you want    Environmentally friendly according to EU directive 2002/95 / EG (RoHS)Technical specifications    Li-ion cell: LG Chem INR21700-M50T    Voltage (nominal): 24V (25.2V - 25.9V)    Capacity: 100Ah    Energy: approx. 2500 Wh    Configuration: 7S20P    Charging voltage: 29.4V    Final discharge voltage: 21V    Charging current (max.): 20A    Continuous discharge current:30A = 750 Watts or 60A = 1500 Watts    Weight: approx. 16 Kg.    Dimensions: 465 x 365 x 185 mm    Charge: Weipu    Discharge connector: WEIPU, or Emphanol  For more Information use please this link

ENERpower Softpack battery 24V in format 7S5P | 360Wh | capacity 15Ah | for Pedelecs, eBikes DIY, Electric Boats, Maschines, Robotics | with Samsung 30T. Important General Information This 24V battery in softpack is in 7S format (25.2V-25.9V) and is manufactured with the battery cells of Samsung SDI, Murata (Sony) or Panasonic. The batteries are manufactured in cell holders made of plastic and equipped with a BMS 40A brand ENERpower. Charging is made with a spiral cable (20 - 100 cm extendable) with a XLR-3 (3 pins) connector. Discharging is realized via a discharge cable with XT90 connector (male). A counterpart XT90 is also included.   This range of small and powerful batteries we assemble with the impressive cell of Samsung SDI INR21700-30T. This battery cell hold a very stable voltage also at high discharge current and can operate 24V devices with up to 1200 Watt consumption.  Thus, this battery is also suitable for motors with 1200 watts of power.We manufacture the softpack batteries with FR4 insulation, flame retardant and flame retardant composites consisting of epoxy resin and glass fiber fabric. FR-4 is used inter alia as an electrically non-conductive substrate in electrical circuit boards. Compatible with 24V motors 250 watts / 350 watts / 500 watts / 750 watts / 1000 / 1200 watts Highlights High-quality production - Made in Germany Production Just-In-Time BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring) Direct from the manufacturer Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity No memory effect - charge the battery whenever you want Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS) Technical Specifications Li-ion battery cell: Samsung SDI INR21700-30T Voltage (nominal): 24V (25.2V – 25.9V) Capacity: 15Ah Energy: approx. 360 Wh Configuration: 7S5P Format: 7 × 5 Internal resistance: < 75 mOhm Charging voltage: 29.4V End-of-discharge voltage: 21V Continuous discharge current: 50A = 1200 Watt 5 Sec. discharge current: 60A = ca. 1440 Watt Charging: up to 8A Discharging temperture: -20 to 80°C Weight: approx. 2.75 kg. Dimensions Length: 160 mm Länge Width: 115 mm – 135 mm Height: 70 mm

ENERpower Softpack battery 24V in format 7S6P | 440Wh | capacity 18Ah | for Pedelecs, eBikes DIY, Electric Boats, Maschines, Robotics | with Samsung 30T. Important General Information This 24V battery in softpack is in 7S format (25.2V-25.9V) and is manufactured with the battery cells of Samsung SDI, Murata (Sony) or Panasonic. The batteries are manufactured in cell holders made of plastic and equipped with a BMS 40A brand ENERpower. Charging is made with a spiral cable (20 - 100 cm extendable) with a XLR-3 (3 pins) connector. Discharging is realized via a discharge cable with XT90 connector (male). A counterpart XT90 is also included.   This range of small and powerful batteries we assemble with the impressive cell of Samsung SDI INR21700-30T. This battery cell hold a very stable voltage also at high discharge current and can operate 24V devices with up to 1200 Watt consumption.  Thus, this battery is also suitable for motors with 1200 watts of power.We manufacture the softpack batteries with FR4 insulation, flame retardant and flame retardant composites consisting of epoxy resin and glass fiber fabric. FR-4 is used inter alia as an electrically non-conductive substrate in electrical circuit boards. Compatible with 24V motors 250 watts / 350 watts / 500 watts / 750 watts / 1000 / 1200 watts Highlights High-quality production - Made in Germany Production Just-In-Time BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring) Direct from the manufacturer Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity No memory effect - charge the battery whenever you want Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS) Technical Specifications Li-ion battery cell: Samsung SDI INR21700-30T Voltage (nominal): 24V (25.2V – 25.9V) Capacity: 18Ah Energy: approx. 440 Wh Configuration: 7S6P Format: 7 × 6 Internal resistance: < 75 mOhm Charging voltage: 29.4V End-of-discharge voltage: 21V Continuous discharge current: 50A = 1200 Watt 5 Sec. discharge current: 60A = ca. 1440 Watt Charging: up to 8A Discharging temperture: -20 to 80°C Weight: approx. 3.35 kg. Dimensions Length: 160 mm Länge Width: 138 mm – 160 mm Height: 70 mm

ENERpower Softpack battery 24V in format 7S7P | 840Wh | capacity 35Ah | for Pedelecs, eBikes DIY | with LG Chem 50M. Important General Information This 24V battery in softpack is in 7S format (25.2V-25.9V) and is manufactured with the battery cells of Samsung SDI, Murata (Sony) or Panasonic. The batteries are manufactured in cell holders made of plastic and equipped with a BMS 40A brand ENERpower. Charging is made with a spiral cable (20 - 100 cm extendable) with a XLR-3 (3 pins) connector. Discharging is realized via a discharge cable with XT90 connector (male). A counterpart XT90 is also included.   A fuse (fuse) of 60A in a waterproof holder limits the current drain and provides an additional safety measure.Thus, this battery is also suitable for motors with 1000 watts of power.We manufacture the softpack batteries with FR4 insulation, flame retardant and flame retardant composites consisting of epoxy resin and glass fiber fabric. FR-4 is used inter alia as an electrically non-conductive substrate in electrical circuit boards.In this battery we have also integrated a charge indicator. In 5 levels (empty / 25% / 50% / 75% / full) you can easily read the battery condition. Compatible with 24V motors 250 watts / 350 watts / 500 watts / 750 watts / 1000 watts Highlights High-quality production - Made in Germany Production Just-In-Time BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring) Samsung SDI INR18650-35E Li-Ion Cells –> 10A continuous load Direct from the manufacturer Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity No memory effect - charge the battery whenever you want Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS) Technical Specifications Li-ion battery cell:LG Chem INR21700 50M Voltage (nominal): 24V (25.2V – 25.9V) Capacity: 35 Ah Energy: approx. 840 Wh Configuration: 7S7P Format: 7×7 Internal resistance: < 75 mOhm Charging voltage: 29.4V End-of-discharge voltage: 21V Continuous discharge current: 20A = 480 Watt 10 Min. discharge current: 40A = 1000 Watt 5 Sec. discharge current: 45A = ca. 1125Watt Weight: approx. 3.65 kg. Dimensions Length: 154 mm Länge Width: 154 mm – 165 mm Height: 70 mm

ENERpower Softpack battery 24V in format 7S10P | 1260Wh | capacity 50Ah | for Pedelecs, eBikes DIY | with Samsung 50E. Important General Information This 24V battery in softpack is in 7S format (25.2V-25.9V) and is manufactured with the battery cells of Samsung SDI, Murata (Sony) or Panasonic. The batteries are manufactured in cell holders made of plastic and equipped with a BMS 40A brand ENERpower. Charging is made with a spiral cable (20 - 100 cm extendable) with a XLR-3 (3 pins) connector. Discharging is realized via a discharge cable with XT90 connector (male). A counterpart XT90 is also included.   A fuse (fuse) of 60A in a waterproof holder limits the current drain and provides an additional safety measure.Thus, this battery is also suitable for motors with 1000 watts of power.We manufacture the softpack batteries with FR4 insulation, flame retardant and flame retardant composites consisting of epoxy resin and glass fiber fabric. FR-4 is used inter alia as an electrically non-conductive substrate in electrical circuit boards. Compatible with 24V motors 250 watts / 350 watts / 500 watts / 750 watts / 1000 watts Highlights High-quality production - Made in Germany Production Just-In-Time BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring) Direct from the manufacturer Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity No memory effect - charge the battery whenever you want Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS) Technical Specifications Li-ion battery cell: Samsung SDI INR21700-50E Voltage (nominal): 24V (25.2V – 25.9V) Capacity: 50Ah Energy: approx. 1260 Wh Configuration: 7S10P Format: 10 ×7 Internal resistance: < 75 mOhm Charging voltage: 29.4V End-of-discharge voltage: 21V Continuous discharge current: 40A = 1000 Watt 5 Sec. discharge current: 50A = ca. 1200 Watt Weight: approx. 5.40 kg. Dimensions Length: 230 mm Länge Width: 160 mm – 175 mm Height: 70 mm

ENERpower Softpack battery 24V in format 7S10P | 1200Wh | capacity 50Ah | for Pedelecs, eBikes DIY | with Samsung 50E. Important General Information This 24V battery in softpack is in 7S format (25.2V-25.9V) and is manufactured with the battery cells of Samsung SDI, Murata (Sony) or Panasonic. The batteries are manufactured in cell holders made of plastic and equipped with a BMS 40A brand ENERpower. Charging is made with a spiral cable (20 - 100 cm extendable) with a XLR-3 (3 pins) connector. Discharging is realized via a discharge cable with XT90 connector (male). A counterpart XT90 is also included.  Thus, this battery is also suitable for motors with 1200 watts of power.We manufacture the softpack batteries with FR4 insulation, flame retardant and flame retardant composites consisting of epoxy resin and glass fiber fabric. FR-4 is used inter alia as an electrically non-conductive substrate in electrical circuit boards. Compatible with 24V motors 250 watts / 350 watts / 500 watts / 750 watts / 1000 / 1200 watts Highlights High-quality production - Made in Germany Production Just-In-Time BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring) Direct from the manufacturer Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity No memory effect - charge the battery whenever you want Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS) Technical Specifications Li-ion battery cell: Samsung SDI INR21700-50E Voltage (nominal): 24V (25.2V – 25.9V) Capacity: 50Ah Energy: approx. 1200 Wh Configuration: 7S10P Format: 10 ×7 Internal resistance: < 75 mOhm Charging voltage: 29.4V End-of-discharge voltage: 21V Continuous discharge current: 50A = 1200 Watt 5 Sec. discharge current: 60A = ca. 1440 Watt Weight: approx. 5.50 kg. Dimensions Length: 230 mm Länge Width: 160 mm – 175 mm Height: 70 mm

ENERpower Softpack battery 24V in format 7S12P | 1500Wh | capacity 60Ah | for Pedelecs, eBikes DIY | with Samsung 50E. Important General Information This 24V battery in softpack is in 7S format (25.2V-25.9V) and is manufactured with the battery cells of Samsung SDI, Murata (Sony) or Panasonic. The batteries are manufactured in cell holders made of plastic and equipped with a BMS 40A brand ENERpower. Charging is made with a spiral cable (20 - 100 cm extendable) with a XLR-3 (3 pins) connector. Discharging is realized via a discharge cable with XT90 connector (male). A counterpart XT90 is also included.   A fuse (fuse) of 60A in a waterproof holder limits the current drain and provides an additional safety measure.Thus, this battery is also suitable for motors with 1000 watts of power.We manufacture the softpack batteries with FR4 insulation, flame retardant and flame retardant composites consisting of epoxy resin and glass fiber fabric. FR-4 is used inter alia as an electrically non-conductive substrate in electrical circuit boards. Compatible with 24V motors 250 watts / 350 watts / 500 watts / 750 watts / 1000 watts Highlights High-quality production - Made in Germany Production Just-In-Time BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring) Direct from the manufacturer Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity No memory effect - charge the battery whenever you want Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS) Technical Specifications Li-ion battery cell: Samsung SDI INR21700-50E Voltage (nominal): 24V (25.2V – 25.9V) Capacity: 60Ah Energy: approx. 1500 Wh Configuration: 7S12P Format: 12 ×7 Internal resistance: < 75 mOhm Charging voltage: 29.4V End-of-discharge voltage: 21V Continuous discharge current: 40A = 1000 Watt 5 Sec. discharge current: 50A = ca. 1200 Watt Weight: approx. 6.50 kg. Dimensions Length: 280 mm Länge Width: 160 mm – 175 mm Height: 70 mm

ENERpower Softpack battery 24V in format 7S12P | 1500Wh | capacity 60Ah | for Pedelecs, eBikes DIY | with Samsung 50E. Important General Information This 24V battery in softpack is in 7S format (25.2V-25.9V) and is manufactured with the battery cells of Samsung SDI, Murata (Sony) or Panasonic. The batteries are manufactured in cell holders made of plastic and equipped with a BMS 40A brand ENERpower. Charging is made with a spiral cable (20 - 100 cm extendable) with a XLR-3 (3 pins) connector. Discharging is realized via a discharge cable with XT90 connector (male). A counterpart XT90 is also included.  Thus, this battery is also suitable for motors with 1200 watts of power.We manufacture the softpack batteries with FR4 insulation, flame retardant and flame retardant composites consisting of epoxy resin and glass fiber fabric. FR-4 is used inter alia as an electrically non-conductive substrate in electrical circuit boards. Compatible with 24V motors 250 watts / 350 watts / 500 watts / 750 watts / 1000 / 1200 watts Highlights High-quality production - Made in Germany Production Just-In-Time BMS with an integrated passive balancer and protection against overcharge, over-discharge, over-discharge (temperature monitoring) Direct from the manufacturer Rechargeable - After 300 charging cycles, still maintains 80% of the original capacity No memory effect - charge the battery whenever you want Environmentally friendly in accordance with EU Directive 2002/95 / EC (RoHS) Technical Specifications Li-ion battery cell: Samsung SDI INR21700-50E Voltage (nominal): 24V (25.2V – 25.9V) Capacity: 60Ah Energy: approx. 1500 Wh Configuration: 7S12P Format: 12 ×7 Internal resistance: < 75 mOhm Charging voltage: 29.4V End-of-discharge voltage: 21V Continuous discharge current: 50A = 1200 Watt 5 Sec. discharge current: 60A = ca. 1440 Watt Weight: approx. 6.50 kg. Dimensions Length: 280 mm Länge Width: 160 mm – 175 mm Height: 70 mm